User Tools

Site Tools


Differences

This shows you the differences between two versions of the page.

Link to this comparison view

playground:mission-log-template [2016/04/19 20:50]
chrono
playground:mission-log-template [2017/07/08 11:09] (current)
chrono
Line 1: Line 1:
 ~~DRAFT~~ ~~DRAFT~~
 +====== GHETTO-RAID Voodoo ======
  
 +https://​www.amazon.de/​gp/​product/​B01H43DNPY/​
 +http://​www.conrad.com/​ce/​en/​product/​1420906/​RAID-controller-card-2x-M2-NGFF-1x-SATA-socket-2-pin
  
 +
 +Manual:
 +
 +<​blockquote>​
 +  - Install M.2 NGFF SATA SSD into M2_1 and M2_2 sockets.
 +  - Set J1 RAID Jumper to your desired mode or RAID initial mode.
 +  - Set J2 jumper to short SET – GND.
 +  - Connect 22-Pin SATA connector to SATA Host and Power.
 +  - Turn on the power.
 +  - Check “Device Manager” the RAID status of M.2 SSD .
 +  - Set J2 jumper to short SET – NC and disable RAID Mode Change
 +<​cite>​[[http://​www.produktinfo.conrad.com/​datenblaetter/​1400000-1499999/​001420906-an-01-ml-H_W_RAID_KONTROLLER_2X_de_en_fr_nl_it_pl.pdf|User Manual]]</​cite>​
 +</​blockquote>​
 +
 +<​code>​
 +[38198.548757] ata6: exception Emask 0x10 SAct 0x0 SErr 0x4090000 action 0xe frozen
 +[38198.548761] ata6: irq_stat 0x00400040, connection status changed
 +[38198.548765] ata6: SError: { PHYRdyChg 10B8B DevExch }
 +[38198.548774] ata6: hard resetting link
 +[38204.283034] ata6: link is slow to respond, please be patient (ready=0)
 +[38208.562937] ata6: COMRESET failed (errno=-16)
 +[38208.562943] ata6: hard resetting link
 +[38214.346804] ata6: link is slow to respond, please be patient (ready=0)
 +[38218.594711] ata6: COMRESET failed (errno=-16)
 +[38218.594718] ata6: hard resetting link
 +[38224.362575] ata6: link is slow to respond, please be patient (ready=0)
 +[38253.649908] ata6: COMRESET failed (errno=-16)
 +[38253.649916] ata6: limiting SATA link speed to 3.0 Gbps
 +[38253.649919] ata6: hard resetting link
 +[38258.665790] ata6: COMRESET failed (errno=-16)
 +[38258.665797] ata6: reset failed, giving up
 +[38258.665803] ata6: EH complete
 +
 +[45419.920134] ​ sdb: sdb1 sdb2 sdb3 sdb4
 +</​code>​
 +
 +In order to reset it was necessary to power off, J2 to SET-GND, J1 to PM, power on, wait a couple of mins, power off, set J1 to R1 (Mirror), leave J2 on SET-GND, power on, 
 +
 +<​code>​
 +[44010.027895] ata6: exception Emask 0x50 SAct 0x0 SErr 0x40d0800 action 0xe frozen
 +[44010.027899] ata6: irq_stat 0x00400040, connection status changed
 +[44010.027904] ata6: SError: { HostInt PHYRdyChg CommWake 10B8B DevExch }
 +[44010.027912] ata6: hard resetting link
 +[44010.757949] ata6: SATA link down (SStatus 0 SControl 300)
 +[44010.757963] ata6: EH complete
 +[44021.865962] ata6: exception Emask 0x10 SAct 0x0 SErr 0x40d0002 action 0xe frozen
 +[44021.865967] ata6: irq_stat 0x00000040, connection status changed
 +[44021.865971] ata6: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch }
 +[44021.865980] ata6: hard resetting link
 +[44023.085667] ata6: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
 +[44023.085944] ata6.00: ATA-7: JMicron H/W RAID1, 32201020, max UDMA/133
 +[44023.085948] ata6.00: 1953431552 sectors, multi 1: LBA48
 +[44023.086236] ata6.00: configured for UDMA/133
 +[44023.086247] ata6: EH complete
 +[44023.086563] scsi 5:0:0:0: Direct-Access ​    ​ATA ​     JMicron H/W RAID 1020 PQ: 0 ANSI: 5
 +[44023.112971] sd 5:0:0:0: Attached scsi generic sg2 type 0
 +[44023.113113] sd 5:0:0:0: [sdb] 1953431552 512-byte logical blocks: (1.00 TB/931 GiB)
 +[44023.113140] sd 5:0:0:0: [sdb] Write Protect is off
 +[44023.113144] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
 +[44023.113200] sd 5:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn'​t support DPO or FUA
 +[44023.114644] sd 5:0:0:0: [sdb] Attached SCSI disk
 +</​code>​
  
 {{tag>​carbon hardware diy 3d-print sourcing}} {{tag>​carbon hardware diy 3d-print sourcing}}