User Tools

Site Tools


Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
Last revisionBoth sides next revision
mission:log:2015:07:07:green-ethernet-switch-review-dlink-dgs-1100-8-managed-switch [2015/07/07 12:17] – created chronomission:log:2015:07:07:green-ethernet-switch-review-dlink-dgs-1100-8-managed-switch [2015/08/30 17:56] – [Reliability & Performance] chrono
Line 11: Line 11:
 ===== Power Consumption Analysis ===== ===== Power Consumption Analysis =====
  
-For better comparison all measurement results have been put together. A couple of people have been a bit unhappy, that we've only documented power consumption on the DC side in the past review (which is all we care about for off-grid usage). As a result, this time we've documented DC and Wall-Power consumption (with the original D-Link AC/DC plug).+For better comparison all measurement results have been put together. A couple of people have been a bit unhappy, that we've only documented power consumption on the DC side in the past review (which is all we care about for off-grid usage). As a result, we've documented DC and Wall-Power consumption with the original D-Link AC/DC plug.
  
 ==== Test-Setup ==== ==== Test-Setup ====
Line 45: Line 45:
 </WRAP> </WRAP>
  
 +===== Under the Hood =====
 +
 +==== PCB ====
 +
 +{{:mission:log:2015:07:07:d-link-dgs-1100-8-board-top.jpg|d-link-dgs-1100-8-board-top}}
 +{{:mission:log:2015:07:07:d-link-dgs-1100-8-board-bottom.jpg|d-link-dgs-1100-8-board-bottom}}
 +
 +==== Serial Console ====
 +
 +{{:mission:log:2015:07:07:d-link-dgs-1100-8-j1-connector-serial.jpg|d-link-dgs-1100-8-j1-connector-serial}}
 +
 +There is some sort of serial console on J1 (576008N1)
 +
 +<code>
 +==========Loader: 1.0.13 (Build: Apr 10 2013, 13:51:22)==========
 +[Loader] dummy_init......
 +
 +
 +==========Loader start===========
 +Press any key to start the normal procedure.
 +To run SPI flash viewer, press [v]
 +To enforce the download of the runtime kernel, press [ESC] 
 +    Check Runtime Image.....
 +    Chksum Correct!
 +    RunTime Kernel Starting....  
 +SalFlshCopyFlshToCache()
 +[FW] dummy_flash_toCache......
 +sal_sys_config_restore()DHCPC is disabled.
 +...OK
 +sal_mirror_config_restore()...OK
 +sal_qos_config_restore()...OK
 +sal_vlan_config_restore()...OK
 +sal_trunk_config_restore()...OK
 +sal_rate_config_restore()...OK
 +sal_port_config_restore()...OK
 +sal_l2_config_restore()...OK
 +sal_loop_config_restore()...OK
 +sal_eee_restore()...OK
 +sal_green_restore()...OK
 +sal_admin_restore()...OK
 +sal_igmp_restore()...OK
 +
 +==========Runtime: 1.10.030 (Build: Oct 17 2014, 12:18:16)==========
 +### dummy_init......OK! 
 +</code>
 ===== Conclusion ===== ===== Conclusion =====