Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| mission:log:2012:07:17:howto-disassemble-a-brushless-motor [2013/06/30 12:34] – [Step 1: Preparations] chrono | mission:log:2012:07:17:howto-disassemble-a-brushless-motor [2015/01/29 13:02] (current) – [HOWTO disassemble a brushless outrunner motor] chrono | ||
|---|---|---|---|
| Line 5: | Line 5: | ||
| {{: | {{: | ||
| - | But how do you take it apart without special tools? The following 7-step HOWTO will guide you through the simple dis-assembly process: | + | In order to progress [[mission: |
| ===== ===== | ===== ===== | ||
| Line 36: | Line 36: | ||
| {{: | {{: | ||
| - | <note tip> | + | <WRAP round tip> |
| * Look for something that is far less dense than steel but still stable enough to transfer the energy from your hammer into the shaft, preferrably without the tendency to splinter. Wood is generally a good choice. | * Look for something that is far less dense than steel but still stable enough to transfer the energy from your hammer into the shaft, preferrably without the tendency to splinter. Wood is generally a good choice. | ||
| * Place it above the shaft and hold it down with one hand. | * Place it above the shaft and hold it down with one hand. | ||
| - | </note> | + | </WRAP> |
| ===== Step 3: Push the shaft ===== | ===== Step 3: Push the shaft ===== | ||
| Line 45: | Line 45: | ||
| {{: | {{: | ||
| - | <note tip> | + | <WRAP round tip> |
| * Use your hammer with the other hand and give it one or more gentle taps until the bell drops to the bottom | * Use your hammer with the other hand and give it one or more gentle taps until the bell drops to the bottom | ||
| * If the bell doesn' | * If the bell doesn' | ||
| - | </note> | + | </WRAP> |
| ===== Step 4: Remove the bell ===== | ===== Step 4: Remove the bell ===== | ||
| - | <note warning> | + | <WRAP round alert> |
| Never underestimate the force of these magnets. At this point and again, when you re-assemble the motor, the bell might easily snap back into its original position by itself if you let it slide too far up again. So please, take special care when executing the next step, because it will hurt, if a part of your skin is getting wedged in between the bell and the base, when they slam home. | Never underestimate the force of these magnets. At this point and again, when you re-assemble the motor, the bell might easily snap back into its original position by itself if you let it slide too far up again. So please, take special care when executing the next step, because it will hurt, if a part of your skin is getting wedged in between the bell and the base, when they slam home. | ||
| - | </note> | + | </WRAP> |
| {{: | {{: | ||
| - | <note tip> | + | <WRAP round tip> |
| * Hold the base steady in one hand and gently remove the bell and the shaft in a downward direction with your other hand | * Hold the base steady in one hand and gently remove the bell and the shaft in a downward direction with your other hand | ||
| - | </note> | + | </WRAP> |
| ===== Step 5: Have a break and enjoy your work ===== | ===== Step 5: Have a break and enjoy your work ===== | ||
| Line 72: | Line 72: | ||
| {{: | {{: | ||
| - | <note tip> | + | <WRAP round tip> |
| * Use a hex bit to remove the screw | * Use a hex bit to remove the screw | ||
| - | </note> | + | </WRAP> |
| ===== Step 7: Go find a tool ===== | ===== Step 7: Go find a tool ===== | ||
| Line 80: | Line 80: | ||
| {{: | {{: | ||
| - | <note tip> | + | <WRAP round tip> |
| * In this case you need something that is smaller in diameter than the shaft but basically has the same requirements as step 2: Less dense than steel, can transfer energy without braking/ | * In this case you need something that is smaller in diameter than the shaft but basically has the same requirements as step 2: Less dense than steel, can transfer energy without braking/ | ||
| * Place the food end of the chopstick at the center of the shaft and gently tap on the top with the hammer until the shaft is driven out. | * Place the food end of the chopstick at the center of the shaft and gently tap on the top with the hammer until the shaft is driven out. | ||
| - | </note> | + | </WRAP> |
| ===== Finally ===== | ===== Finally ===== | ||